Fortinet Fortinet Network Security Expert NSE8_811

近年に、Fortinet NSE8_811 「Fortinet NSE 8 Written Exam (NSE8_811)」 認定試験は重要なコンピュータ能力認定試験になっています。Fortinet 国際認証資格取得者になったら、求職がもっと易く、高給料も当たり前です！

でも、どうやって簡単的にスムーズに Fortinet NSE8_811 試験を合格しますか、JapanCert会社だ！助けるよ。

JapanCertは国際ＩＴ認証試験資料集を提供するＷｅｂです。JapanCert会社は最良最新の試験資料の資源です、JapanCert会社が提供する Fortinet 認定資格試験問題集は豊富な経験のＩＴ専家に過去試験より一生懸命に研究する出題傾向のです。

問題集の正確率は９９％になって、１００％に合格できて、安心に試験しましょう。

我社の Fortinet NSE8_811 は今では最新の問題集で、試験範囲を１００％網羅して一番な試験助手になります。20時間から３０時間ぐらいかかるなら、内容を覚えるだけいいです。

問題集がいつも最新の状態を持つために、Fortinet NSE8_811 認証問題集を購入いただくお客様が一年の更新サービスを無料に提供します。もしこちらで提供する問題集を使用して未合格したら、Prometric或いはVUE発行する成績を確認後、全額に返金します、絶対にお金を無駄にならない。

JapanCert試験問題集はPDF版とソフト版を提供します。PDF版は印刷されることができます、ソフト版はどのパソコンでも使われることもできます。

JapanCertの試験資料を買うかどうかと迷ったら、Fortinet NSE8_811 「Fortinet NSE 8 Written Exam (NSE8_811)」 試験の部分問題と回答を無料にダウンロードして試用する後、決めて信じてくれます。早ければJapanCertを信じてくれて、早く成功になっています。

簡単で便利な購入方法：ご購入を完了するためにわずか2つのステップが必要です。弊社は最速のスピードでお客様のメールボックスに製品をお送りします。あなたはただ電子メールの添付ファイルをダウンロードする必要があります。

NSE8_811オンライン版は Windows / Mac / Android / iOS 対応です。

Fortinet NSE 8 Written Exam (NSE8_811) 認定 NSE8_811 試験問題:

1. Refer to the exhibit.

The exhibit shows a full-mesh topology between FortiGate and FortiSwitch devices. To deploy this configuration, two requirements must be met:
* 20 Gbps full duplex connectivity is available between each FortiGate and the FortiSwitch devices
* The FortiGate HA must be in AP mode
Referring to the exhibit, what are two actions that will fulfill the requirements? (Choose two.)

A) Configure the master FortiGate with one LAG and FortiLink split interface disabled on ports connected to cables A and C and make sure the same ports are used for cables B and D on the slave.
B) Configure both FortiSwitch devices as peers with ISL over cable E, create one MCLAG on ports connected to cables A and C, and create another MCLAG on ports connected to cables B and D.
C) Configure the master FortiGate with one LAG and FortiLink split interface enabled on ports connected to cables A and C and make sure the same ports are used for cables B and D on the slave.
D) Configure both FortiSwitch devices as peers with ICL over cable E, create one MCLAG on ports connected to cables A and C, and create another MCLAG on ports connected to cables B and D.

2. A FortOS devices is used for termination of VPNs for number of remote spoke VPN units (designated group A spokes) using a phase 1 main mode dial-up tunnel using pre-shared. Your company recently acquired another organization. You are asked establish VPN correctively for the newly acquired organization's sites which new devices will be provisioned (designated Group B spokes). Both exiting (Group A) and new (Group B) spoke units are dynamically addressed. You are asked to ensure that spokes from the acquired organization (Group B) have different access permission than your existing VPN spokes (Group A).
Which two solutions meet the represents for the new spoke group? (Choose two.)

A) Implement a new phase 1 dial-up main mode tunnel with certificate authentication.
B) Implement a new phase 1 dial-up main mode tunnel with a different pre-shared key than the Group A
spokes.
C) Implement a new phase 1 dial-up main mode tunnel with pre-shared keys and XAuth.
D) Implement separate phase 1 dial-up aggressive mode tunnels with a distinct peer ID.

3. Refer to the exhibit.

The FortiAP profile used by the FortiGate managed AP is shown in the exhibit.
Which two statements in this scenario are correct? (Choose two.)

A) Interference will be prevented between FortiAP devices using this profile.
B) All FortiAP devices using this profile will have Radio 1 monitor wireless clients.
C) This profile will map specific SSIDs available to the FortiAP devices.
D) All FortiAP devices using this profile will have Radio 1 scan rogue access points.

4. You deploy a FortiGate device in a remote office based on the requirements shown below.
-- Due to company's security policy, management IP of your FortiGate is not allowed to access the Internet.
-- Apply Web Filtering, Antivirus, IPS and Application control to the protected subnet.
-- Be managed by a central FortiManager in the head office.
Which action will help to achieve the requirements?

A) Configure the FortiGuard override server and use the IP address of service, fortiguard net.
B) Configure a default route and make sure that the FortiGate device can pmg to service fortiguard net.
C) Configure FortiGate to use FortiGuard Filtering Port 8888.
D) Configure the FortiGuard override server and use the IP address of the FortiManager

5. Click the Exhibit button.

Referring to the exhibit, which two statements are true? (Choose two.)

A) LAG-3 on switches on FS448D-A and FS448D-B may be connected to a single 802 3ad trunk on another device.
B) LAG-1 and LAG 2 should be connected to a single 4-port 802 3ad interface on the FortiGate-A.
C) port13 and port14 on FS448D-A should be connected to port13 and port14 on FS448D-B.
D) LAG-1 and LAG-2 should be connected to a 4-port single 802 3ad trunk on another device.

質問と回答：